RVK 250 mm Extractor A1 (860 m3/h)

Buy RVK Extractor 250 mm. A1 (860 M3/H) for indoor growing

The RVK Extractor 250 mm. A1 (860 M3/H) is designed to work for many hours without losing performance, maintaining a remarkable balance between available pressure and quiet operation.

The reinforced technical plastic housing offers mechanical resistance and tolerance to humid environments; the centrifugal impeller and internal directional plates reduce turbulence and increase efficiency, which is essential when the circuit includes an activated carbon filter, silencers, and duct sections. The 250 mm standard ensures compatibility with flexible or rigid ducts, reducers, and mounting flanges.

With a nominal flow rate of 860 m³/h, this unit extracts accumulated heat, reduces excess humidity, and renews CO₂ evenly throughout the entire volume of the grow tent.

The electronics incorporate thermal protection with reset, and the unit allows speed regulation through a suitable controller, making it easy to fine-tune at every stage of the grow.

The IP44 protection rating enables safe installation in demanding environments. In the Hydroponics Blanes catalog, Grow Shop in Spain, it is possible to complete the installation with clamps, aluminum tape, reducers, controllers, pre-filters, and a wide selection of cannabis growing accessories and cheap indoor grow tents, backed by the support of a trusted Grow Shop with discreet shipping.

Indoor Growing Extractor RVK 250 mm. A1 (860 M3/H)

A well-sized extraction system stabilizes temperature and humidity, prevents dead zones, and promotes homogeneous gas exchange. The RVK Extractor 250 mm. A1 (860 M3/H) performs especially well in medium-sized tents with LED or moderate HPS, and in compact rooms that require constant 24/7 ventilation.

What is the RVK Extractor 250 mm. A1 (860 M3/H) for?

• Continuous air renewal: removal of heat and vapor to keep VPD in productive ranges.
• Odor control: direct integration with 250 mm filters compatible with the flow rate.
• Useful pressure: ability to overcome losses in elbows, pre-filters, and silencers.
• Overall efficiency: more flow with less turbulence and lower aerodynamic noise.

Indoor growing accessory RVK Extractor 250 mm. A1 (860 M3/H)

Among the essential cannabis growing accessories, this model stands out for its robustness, reliability, and compatibility with most 250 mm components. The unit operates stably during long cycles, which is key to maintaining a controlled climate in tents and work rooms.

What is the RVK Extractor 250 mm. A1 (860 M3/H) used for?

Recommended use as the main extractor in 120×240 cm tents or compact rooms (always sizing according to lighting power and duct length). It also fits as a regulated intake fan in spaces that require filtered fresh air, and in drying areas where a constant flow is needed to prevent humidity spikes.

How to use RVK Extractor 250 mm. A1 (860 M3/H)

1. Calculate target flow: room volume (m³) × air changes/hour (30–60 as a reference) and add losses from filter and elbows.
2. Place the extractor at the top of the tent or room to evacuate hot air; place inlets at the bottom for even sweeping.
3. Connect to 250 mm duct; seal joints with aluminum tape and secure with metal clamps.
4. Attach a 250 mm carbon filter when odor control is a priority; select a model sized for 860 m³/h.
5. Minimize elbows and long runs; a straight layout preserves pressure and reduces noise.
6. Regulate speed using a controller suitable for compatible motors; adjust according to season and stage of the grow.
7. Maintenance plan: clean pre-filters, inspect ducts, check fastenings, and periodically check for vibrations.

Advantages of using RVK Extractor 250 mm. A1 (860 M3/H)

• Powerful flow of 860 m³/h with stable centrifugal thrust.
• Quiet operation compared to axial solutions of the same size.
• Total compatibility with 250 mm ducts, filters, and silencers.
• IP44 protection and thermal protection with reset for greater safety.
• Easy installation and minimal maintenance in intensive setups.

Where to buy an RVK Extractor 250 mm. A1 (860 M3/H) online?

Available at Hydroponics Blanes with expert advice from a trusted Grow Shop, discreet shipping, and everything you need for indoor growing: controllers, ducts, clamps, filters, and cheap indoor grow tents. Safe shopping at a Grow Shop in Spain with extensive experience.

Anyone looking for powerful ventilation, quiet operation, and broad compatibility will find a solid ally in the RVK Extractor 250 mm. A1 (860 M3/H).

This unit makes it easy to maintain a stable climate all year round, with quick integration into 250 mm lines and availability of spare parts and accessories at Hydroponics Blanes, always with close attention and the option of discreet shipping to your home.