RVK 100 mm Extractor A1 (160 m3/h)

Extractor RVK 100 mm. A1 (160 M3/H) for grow tents

The Extractor RVK 100 mm. A1 (160 M3/H) is a compact fan for grow tents and grow rooms that prioritizes reliability, energy efficiency, and low noise. The high-strength technical plastic housing withstands continuous use and the humidity conditions typical in technical gardening.

The centrifugal rotor balances pressure and airflow to work with carbon filters and short duct runs. The A1 version delivers a nominal 160 m³/h and can reach up to 184 m³/h as a maximum indicative value depending on the installation.

The unit allows direct coupling to Ø102 mm flexible duct using clamps, which simplifies integration in starter tents, mother rooms, or small drying rooms.

With an approximate consumption of 29 W, the unit extracts accumulated heat, reduces excess humidity, and renews CO₂ without raising the ambient noise level. This extractor fits projects that require improved air circulation 24/7 to avoid growth stoppages due to heat stress.

In the Hydroponics Blanes catalog, Grow Shop in Spain, it is found alongside cannabis growing accessories, clamps, reducers, filters, and cheap indoor grow tents, with service from a trusted Grow Shop and discreet shipping.

Indoor Growing Extractor RVK 100 mm. A1 (160 M3/H)

In small and medium indoor grow setups, this extractor stabilizes temperature and humidity, prevents dead zones, and helps control odors when integrated with carbon filtration. Lightweight format, reduced dimensions, and minimal maintenance facilitate a homogeneous microclimate throughout the volume.

What is the Extractor RVK 100 mm. A1 (160 M3/H) for?

• Continuous air renewal: removal of heat and vapor to maintain proper VPD.
• Odor control: compatibility with 100 mm carbon filters.
• Useful pressure: ability to overcome moderate losses in short runs and gentle bends.
• Efficiency: balance between 160 m³/h nominal and 29 W consumption.

Indoor growing accessory Extractor RVK 100 mm. A1 (160 M3/H)

Considered among the essential cannabis growing accessories, the Extractor RVK 100 mm. A1 (160 M3/H) stands out for its robustness, low noise, and compatibility with standard ducts and grilles. High-strength plastic material, stable centrifugal drive, and clamp mounting ensure quick and clean installation.

What is the Extractor RVK 100 mm. A1 (160 M3/H) used for?

Recommended use as the main extractor in compact tents (e.g., 60×60, 80×80, 100×100 cm, depending on light power), as an intake fan for regulated fresh air supply, or as support in drying rooms where a constant, gentle flow is needed to avoid humidity spikes.

How to use Extractor RVK 100 mm. A1 (160 M3/H)

1. Calculate required airflow: tent volume (m³) × air changes/hour (30–60 as a general reference).
2. Place at the top of the tent to evacuate accumulated hot air; plan a short run with few bends.
3. Attach to Ø102 mm flexible duct or 100 mm rigid duct; seal joints with aluminum tape and secure with clamps.
4. Integrate 100 mm carbon filter when odor neutralization is needed; minimize pressure losses.
5. Check draft with manual test or anemometer; ensure there are no leaks or undue vibrations.
6. Schedule light maintenance: clean grilles and periodically check duct condition to maintain 160 m³/h nominal.

Advantages of using Extractor RVK 100 mm. A1 (160 M3/H)

• Quiet and stable for many hours of operation without disturbance.
• Low consumption of ≈29 W with useful airflow in compact spaces.
• Durable construction in technical plastic designed for humid environments.
• Compatibility with 102/100 mm ducts, filters, and lightweight silencers.
• Easy installation with clamps and minimal tool use.

Where to buy an Extractor RVK 100 mm. A1 (160 M3/H) online?

At Hydroponics Blanes the Extractor RVK 100 mm. A1 (160 M3/H) is available with expert advice from a trusted Grow Shop, discreet shipping, and everything needed for indoor growing: controllers, ducts, filters, and cheap indoor grow tents. Secure shopping at Grow Shop in Spain.

Indicative technical sheet: Nominal airflow 160 m³/h • Max airflow 184 m³/h • Port 100 mm (compatible with Ø102 mm flexible) • Consumption 29 W • Type Model A1 • Centrifugal drive • High-strength plastic housing.

For projects requiring efficient ventilation and compact size, the Extractor RVK 100 mm. A1 (160 M3/H) is a practical choice: stable airflow, low consumption, and quick installation allow you to maintain a homogeneous climate. With support from Hydroponics Blanes and discreet shipping, it is easy to complete indoor growing setups with reliable performance all year round.