Agua de grifo en cultivo indoorAgua de grifo en cultivo indoor

Can you use tap water for indoor growing straight from the tap? Should you mix it with reverse osmosis water or add CalMag? Before you open the fertiliser, look up two figures in your water report: how many milligrams of calcium and magnesium does each litre already contain?

At Hydroponics Blanes, we’ve chosen a publicly available water report from our town to show you how to read it. We’ll explain what hardness and alkalinity tell you, how to compare the conductivity in the report with your meter reading, and what changes when you fill a watering can with equal parts tap water and reverse osmosis water.

Where to find your local tap water report

In Spain, you can use the SINAC water supply network search tool. Select your autonomous community, province and municipality. If several networks appear, check which one serves your address. You can also look for the water quality section on the website of the supplier named on your water bill.

When you open the report, check the sampling date, the sampling location and the results column. Some reports list a reference value next to the measured result, and it’s easy to mistake one for the other. Look for calcium, magnesium, total hardness, alkalinity, conductivity and pH. If the latest report lists only a few parameters, check the most recent full analysis for the same network.

Tap water for indoor growing
Tap water for indoor growing

A real example: what’s in a watering can filled with water from Blanes?

Report no. 2688514 from Aigües de Blanes covers a sample collected on 29 December 2025 from the storage tank at the drinking water treatment plant in Blanes, in the province of Girona. The laboratory completed the analysis on 27 January 2026. The figures in the table describe the water in that tank on the sampling date. You can check them on pages 3 and 7 of the original Aigües de Blanes report (PDF).

Six results from the Blanes water analysis and how to interpret them before watering
Parameter Result What it tells you
Calcium 42 mg/L Each litre supplies 42 mg of calcium before you add fertiliser.
Magnesium 8 mg/L Each litre supplies 8 mg of magnesium before you add fertiliser.
Total hardness 137 mg/L as CaCO3 This expresses the combined contribution of dissolved minerals to hardness, mainly calcium and magnesium, on a common scale.
Total alkalinity 109.2 mg/L This measures the water’s capacity to neutralise acids. The report gives the value in mg/L without specifying the reference substance.
Electrical conductivity (EC) 562 µS/cm at 20 °C This is equivalent to 0.562 mS/cm at the same reference temperature.
pH 7.7 This is the pH measured in the water sample before any nutrients are added.

What do those figures mean for your watering can? Fill it with 5 litres of the water in this example and it already contains 210 mg of calcium and 40 mg of magnesium. Multiply the concentration of each element in mg/L by the number of litres you use. If your fertiliser chart gives values in mg/L, compare the original concentrations directly: 42 mg/L of calcium and 8 mg/L of magnesium.

Hardness and alkalinity: which figure should you check?

How much calcium and magnesium does your irrigation water supply?

Look for the entries for calcium (Ca) and magnesium (Mg). Total hardness reflects the combined effect of these two minerals. That’s why a hardness of 137 mg/L is consistent with a calcium concentration of 42 mg/L in this example: hardness is expressed as a calcium carbonate equivalent. Adding those 137 mg to the amounts of calcium and magnesium would count part of the same contribution twice.

Some water suppliers report hardness in French degrees of hardness (°f). One French degree equals 10 mg/L as CaCO3. In the Blanes example, 137 mg/L is equivalent to 13.7 °f. This conversion is useful if your local water report and your fertiliser instructions use different scales.

Why can two water samples with the same pH respond differently?

The pH tells you how acidic or alkaline the water is when you measure it. Alkalinity tells you how much acid the water can neutralise, largely thanks to dissolved bicarbonate. Imagine two jugs containing the same volume of water, both starting at pH 7.7. If you add the same amount of pH reducer to each, the pH may drop less in the jug with higher alkalinity. That’s why it’s worth measuring again when you switch water sources.

Alkalinity also matters when growing in pots. Over several waterings, water with high alkalinity can gradually raise the pH of the growing medium. The effect also depends on the fertiliser and the medium you use. If you notice an upward trend, record the pH of your irrigation solution and the pH of the growing medium separately. Use the same method each time you take a particular measurement so you can compare results over time.

Does a high EC mean the water contains enough calcium?

Electrical conductivity reflects the contribution of all the dissolved ions. Alongside calcium and magnesium, the laboratory found 68.5 mg/L of sodium and 115 mg/L of chloride in the Blanes sample. All of these contribute to the reading. If your meter shows 0.56 mS/cm at home, your local water report can help you identify which minerals contribute to that figure.

You can measure conductivity at home with the COM-100 HM conductivity meter. Select EC mode and take two readings: one from the tap water alone and another after you’ve added the fertiliser and mixed it thoroughly. Record both in the same unit. The difference tells you how much the conductivity changed as you prepared the irrigation water.

When comparing your first reading with the local water report, check the reference temperature too. The Blanes report gives conductivity at 20 °C. For a refresher on the units and the measurement procedure, see our guide to measuring EC when growing indoors.

How to choose between tap water, CalMag and reverse osmosis water

Check your base fertiliser before adding CalMag

With the water in our example, you start with 42 mg/L of calcium and 8 mg/L of magnesium. The next figures you need are on the label or technical data sheet for your base fertiliser. Check how much calcium and magnesium it supplies at the dose you use. If the manufacturer offers separate formulas for hard and soft water, check how it defines each category and compare that with your water report.

Pay attention to the units as well. Some labels express calcium and magnesium content as CaO and MgO, while the laboratory reports the elements themselves as Ca and Mg in mg/L. To compare what the water and fertiliser each supply, you need to express both contributions in the same units and account for the fertiliser dose. If the manufacturer provides a chart showing the mg/L of calcium and magnesium supplied at your chosen dose, use that chart.

If you use reverse osmosis water or water with a low mineral content and find that your base fertiliser supplies too little calcium or magnesium, Hydroponics Blanes stocks Green House CalMag in a 1 kg pack. Follow the manufacturer’s directions, taking into account your source water and the fertiliser you already use. For help deciding when to supplement, see our guide to calcium, magnesium and using CalMag when growing indoors.

What changes when you mix tap water with reverse osmosis water?

Imagine filling the same 5-litre watering can with 2.5 litres of Blanes water and 2.5 litres of reverse osmosis water containing negligible amounts of calcium and magnesium. Before adding fertiliser, the blend would contain approximately 21 mg/L of calcium and 4 mg/L of magnesium. Diluting the tap water would also lower the sodium and chloride concentrations. The 50:50 blend illustrates the calculation. To choose a ratio at home, use the figures for the two water sources you actually plan to mix.

Averaging the two pH readings can give a misleading result. Measure the pH of the blend directly, add the nutrients in the order specified by the manufacturer, then check the pH and EC of the finished solution. If you’re considering installing a system, our guide to reverse osmosis water for indoor growing covers the advantages, drawbacks and steps for preparing irrigation water.

What to record before your next watering

Note the sampling date and supply network listed in the report, along with three values: calcium, magnesium and alkalinity. When you fill your watering can, add the volume, the proportion of tap water, the fertiliser dose and the final pH and EC readings to your notes. That gives you two batches to compare if you later change fertilisers or adjust the proportion of reverse osmosis water. If you have a water treatment system at home, always take your sample from the tap you use to fill the reservoir. That’s the water your plants receive.

The Hydroponics Blanes blog is for information only. Our shop supplies fertilisers, nutrients, measuring equipment, irrigation systems and lighting for home growing. We do not sell cannabis containing THC. Smoking is harmful to your health.